Incubator IN30
Temperature / Setting temperature range — +20 to +80 °C
Temperature / Working temperature range — at least 5 above ambient temperature to +80 °C
Temperature / Setting accuracy temperature — 0.1 °C
Temperature / Temperature sensor — 1 Pt100 sensor DIN class A in 4-wire-circuit
Control technology / ControlCOCKPIT — SingleDISPLAY. Adaptive multifunctional digital PID-microprocessor controller with high-definition TFT-colour display
Control technology / Timer — Digital backwards counter with target time setting, adjustable from 1 minute to 99 days
Control technology / Function SetpointWAIT — the process time does not start until the set temperature is reached
Control technology / Calibration — three freely selectable temperature values
Control technology / adjustable parameters — temperature (Celsius or Fahrenheit), air flap position, programme time, time zones, summertime/wintertime
Ventilation / Convection — natural convection
Ventilation / Fresh air — Admixture of pre-heated fresh air by electronically adjustable air flap
Ventilation / Vent — vent connection with restrictor flap
Communication / Documentation — programme stored in case of power failure
Communication / Programming — AtmoCONTROL software for reading out, managing and organising the data logger via Ethernet interface (temporary trial version can be downloaded). USB stick with AtmoCONTROL software available as accessory (on demand).
Safety / Temperature control — adjustable electronic overtemperature monitor and mechanical temperature limiter TB, protection class 1 according to DIN 12880 to switch off the heating approx. 20°C above nominal temperature
Safety / Autodiagnostic system — for fault analysis
Standard equipment / Works calibration certificate — incl. works calibration certificate for +37°C
Standard equipment / Door — fully insulated stainless steel door with 2-point locking (compression door lock)
Standard equipment / Door — inner glass door
Standard equipment / Internals — 1 stainless steel grid(s), electropolished
Stainless steel interior / Interior — easy-to-clean interior,made of stainless steel, reinforced by deep drawn ribbing with integrated and protected large-area heating on four sides
Stainless steel interior / Volume — 32 l
Stainless steel interior / Dimensions — w (A) x h (B) x d (C) : 400 x 320 x 250 mm
Stainless steel interior / Max. number of internals — 3
Stainless steel interior / Max. loading of chamber — 60 kg
Stainless steel interior / Max. loading per internal — 20 kg
Textured stainless steel casing / Dimensions — w (D) x h (E) x d (F) : 585 x 704 x 434 mm (d +56mm door handle)
Textured stainless steel casing / Housing — rear zinc-plated steel
Electrical data / Voltage
Electrical load — 230 V, 50/60 Hz
approx. 1600 W
Electrical data / Voltage
Electrical load — 115 V, 50/60 Hz
approx. 800 W
Ambient conditions / Set Up — The distance between the wall and the rear of the appliance must be at least 15 cm. The clearance from the ceiling must not be less than 20 cm and the side clearance from walls or nearby appliances must not be less than 5 cm.
Ambient conditions / Altitude of installation — max. 2,000 m above sea level
Ambient conditions / Ambient temperature — +5 °C to +40 °C
Ambient conditions / Humidity rh — max. 80 %, non-condensing
Ambient conditions / Overvoltage category — II
Ambient conditions / Pollution degree — 2
Packing/shipping data / Transport information — The appliances must be transported upright
Packing/shipping data / Customs tariff number — 8419 8998
Packing/shipping data / Country of origin — Federal Republic of Germany
Packing/shipping data / WEEE-Reg.-No. — DE 66812464
Packing/shipping data / Dimensions approx incl. carton — w x h x d: 660 x 890 x 650 mm
Packing/shipping data / Net weight — approx. 48 kg
Packing/shipping data / Gross weight carton — approx. 64 kg
